Motorhome Tools

How do I check my motorhome's alloy wheels can carry its weight?

Quick answer: with single rear wheels, each wheel must be rated for at least half the plated limit of its axle. Check front and rear separately.

Then screen the exact wheel and tyre in our wheel & tyre checker. Ask the seller for the wheel's load certificate in writing. Have a qualified fitter confirm the physical installation.

Isn't a strong tyre enough?

No. The tyre's load index and the wheel's maximum load are separate limits, and each must be high enough on its own. The weakest part sets the limit. A wheel of the right size and bolt pattern isn't automatically rated for a heavy motorhome, and some van alloys are aimed at lighter vehicles.

Where do I find each figure?

Axle limits. Use the front and rear axle figures on the VIN plate (or uprating certificate). Not a brochure figure or the overall weight.

Wheel load rating. Wheel makers say to look on the back of the wheel for a "Max Load" marking, usually behind the spokes, on the inner barrel or around the hub (Wheel Pros, Onyx Forged Wheels). Not every wheel is marked: one owner found his factory alloys had no load stamp. The most reliable source is the wheel maker's data sheet or certificate for the exact part number. If you're buying, get the per-wheel rating from the seller in writing.

Some wheels carry a test mark. One retailer advises looking for "JWL-T" rather than plain "JWL" on van wheels. A mark is a prompt to ask for the load figure, not the figure itself.

Don't mistake PCD for a weight. PCD (pitch circle diameter) is the size of the circle the wheel bolts sit on, in millimetres. So "118" or "130" on a wheel or in an advert is usually the PCD, not a load. One owner made exactly this mistake. If you can't find a clearly labelled load figure, treat the rating as unknown.

How do I do the sum?

Halve each axle limit. That's the minimum rating for each single wheel on that axle. It's standard practice; Rogue Alloy runs the same check online.

Worked example (illustration only): a rear axle plated at 2,500 kg needs each wheel rated at least 1,250 kg. MotorhomeFun members worked through this case: a 1,200 kg wheel was too low, and a 1,450 kg wheel covered it. Use your own VIN plate.

A common shortcut, total weight divided by four, assumes the weight is spread evenly. As Wheel City puts it, that "does not establish the requirement at either axle". Use the per-axle check.

Twin rear wheels (four on the rear axle) share the load differently, so the halving rule doesn't apply. Ask the wheel maker or a specialist fitter.

What about the tyres?

The load index is a number on the tyre sidewall, just before the speed letter, that stands for the most weight the tyre can carry. On "121/120R", the first number is for single fitment and the second for twin (dual) fitment.

The GOV.UK MOT manual's load-index table gives "121/120 = 2,900 single, 5,600 dual". Those figures appear to be per axle (a pair of tyres), so about 1,450 kg per tyre. GOV.UK doesn't say so in words, so check with DVSA or your MOT tester if it matters for your van. Many other tables give the figure per tyre, so check which kind you're reading.

TyreSafe advises never fitting tyres with a lower load capacity or speed rating, and keeping the same size and markings across an axle.

Will the MOT catch a wrong wheel or tyre?

Don't rely on it. An MOT pass isn't proof that your wheels and tyres are rated for your axles, so if you need certainty, ask your MOT tester or DVSA.

What does the checker add?

The hard part is whether this wheel with this tyre clears both plated axle limits, and what evidence backs the wheel's rating. The wheel & tyre checker checks the exact pairing against the front and rear limits you enter from your VIN plate. It cites the wheel maker's certificate or published data where one exists. If a rating isn't publicly sourced, it shows Unverified, never a pass.

It's a screening aid, not a "safe to fit" verdict. It doesn't check clearance, brakes, wheel bolts, speed rating or twin rear wheels.

Do I need to tell my insurer?

Yes. New wheels are generally treated as a modification, and Practical Motorhome advises telling them. One owner was quoted an extra premium; others report no change.

Before you buy: checklist

  1. Note the front and rear axle limits from your VIN plate or uprating certificate.
  2. Halve each one to get the minimum rating per single wheel.
  3. Get the wheel's load rating for the exact part number, in writing.
  4. Check the tyre load index covers each axle.
  5. Run the pair through the checker.
  6. Have a qualified fitter confirm the bolt pattern, centre bore, offset, bolts or nuts and clearance. The centre bore is the hole in the middle of the wheel that fits over the hub. Offset (marked "ET") is how far in or out the wheel sits, in millimetres.
  7. Tell your insurer.

Next step

Enter your VIN plate axle limits in the wheel & tyre checker to screen an exact wheel and tyre pairing. Missing evidence shows as Unverified, never a pass. Have a qualified fitter confirm the installation.